SR Replication Segment for Multi-point Service Delivery

Replication segment is a new type of segment for Segment Routing , which allows a node (henceforth called as Replication Node) to replicate packets to a set of other nodes (called Downstream Nodes) in a Segment Routing Domain. Replication segments provide building blocks for Point-to-Multipoint Service delivery via SR Point-to-Multipoint (SR P2MP) policy. A Replication segment can replicate packet to directly connected nodes or to downstream nodes (without need for state on the transit routers). This document focuses on the Replication segment building block. The use of one or more stitched Replication segments constructed for SR P2MP Policy tree is specified in .

Multi-point Service: A service that has multiple endpoints. A packet is delivered to all the endpoints. Replication Segment: A segment in SR domain that replicates packets. Replication Node: A node in SR domain which replication packets based on Replication Segment Downstream Nodes: A Replication Node replicates packets to a set of Downstream Nodes Replication-ID: Identifier of a Replication Segment at Replication Node Replication State: This is state of Replication Segment at a Replication Node. It is conceptually a list of replication branches to Downstream nodes. The list can be empty. Replication SID: Data plane identifier of a Replication Segment. This is a SR-MPLS label or SRv6 SID.

In a Segment Routing Domain, a Replication segment is a logical construct which connects a Replication Node to a set of Downstream Nodes. A Replication segment is a local segment instantiated at a Replication node. It can be either provisioned locally on a node or programmed by a PCE. Replication segments apply equally to both Segment Routing over MPLS (SR-MPLS) and IPv6 (SRv6). A Replication segment is identified by the tuple <Replication-ID, Node-ID>, where: Replication-ID: An identifier for a Replication segment that is unique in context of the Replication Node. Node-ID: The address of the Replication Node that the Replication segment is for. Note that the root of a multi-point service is also a Replication Node. Replication-ID is a variable length field. In simplest case, it can be a 32-bit number, but it can be extended or modified as required based on specific use of a Replication segment. When the PCE signals a Replication segment to its node, the <Replication-ID, Node-ID> tuple identifies the segment. Examples of such signaling and extension are described in . A Replication segment includes the following elements: Replication SID: The Segment Identifier of a Replication segment. This is a SR-MPLS label or a SRv6 SID . Downstream Nodes: Set of nodes in Segment Routing domain to which a packet is replicated by the Replication segment. Replication State: See below. The Downstream Nodes and Replication State of a Replication segment can change over time, depending on the network state and leaf nodes of a multi-point service that the segment is part of. Replication SID identifies the Replication segment in the forwarding plane. At a Replication node, the Replication SID is the equivalent of Binding SID of a Segment Routing Policy. Replication State is a list of replication branches to the Downstream Nodes. In this document, each branch is abstracted to a <Downstream Node, Downstream Replication SID> tuple. <Downstream Node> represents the reachability from the Replication Node to the Downstream Node. In its simplest form, this MAY be specified as an interface or next-hop if downstream node is adjacent to the Replication Node. The reachability may be specified in terms of Flex-Algo path (including the default algo) , or specified by an SR explicit path represented either by a SID-list (of one or more SIDs) or by a Segment Routing Policy . Downstream Replication SID is the Replication SID of the Replication Segment at the Downstream Node. A packet is steered into a Replication segment at a Replication Node in two ways: When the Active Segment is a locally instantiated Replication SID By the root of a multi-point service based on local configuration outside the scope of this document. In either case, the packet is replicated to each Downstream node in the associated Replication state. If a Downstream Node is an egress (aka leaf) of the multi-point service, i.e. no further replication is needed, then that leaf node's Replication segment will not have any Replication State i.e. the list of Replication branches is empty. The Replication segment will have an indicator role of the node is Leaf. The operation performed on incoming Replication SID is NEXT. At an egress node, the Replication SID MAY be used to identify that portion of the multi-point service. Notice that the segment on the leaf node is still referred to as a Replication segment for the purpose of generalization. A node can be a bud node, i.e. it is a Replication Node and a leaf node of a multi-point service at the same time . Replication Segment of a Bud Node has a list of Replication Branches as well as Leaf role indicator. In principle it is possible for different Replication Segments to replicate packets to the same Replication Segment on a Downstream Node. However, such usage is intentionally left out of scope of this document.

When the Active Segment is a Replication SID, the processing results in a POP operation and lookup of the associated Replication state. For each replication in the Replication state, the operation is a PUSH of the downstream Replication SID and an optional segment list on to the packet which is forwarded to the Downstream node. For leaf nodes the inner packet is forwarded as per local configuration. When the root of a multi-point service steers a packet to a Replication segment, it results in a replication to each Downstream node in the associated replication state. The operation is a PUSH of the replication SID and an optional segment list on to the packet which is forwarded to the downstream node. There MAY be SIDs preceding the SR-MPLS Replication SID in order to guide a packet from a non-adjacent SR node to a Replication Node. A Replication Node MAY replicate a packet to a non-adjacent Downstream Node using SIDs it inserts in the copy preceding the downstream Replication SID. The Downstream Node may be leaf node of the Replication Segment, or another Replication Node, or both in case of bud node. A Replication Node MAY use an Anycast SID or BGP PeerSet SID in segment list to send a replicated packet to one downstream Replication node in an Anycast set if and only if all nodes in the set have an identical Replication SID and reach the same set of receivers. There MAY be SIDs after the Replication SID in the segment list of a packet. These SIDs are used to provide additional context for processing a packet locally at the node where the Replication SID is the Active Segment. The processing of SIDs following the Replication SID MUST NOT forward the SR-MPLS packet to another node.

In SRv6 , the “Endpoint with replication” behavior (End.Replicate for short) replicates a packet and forwards the packet according to a Replication state. When processing a packet destined to a local Replication-SID, the packet is replicated to Downstream nodes and/or locally delivered off tree (when this is a bud/leaf node) according to the associated replication state. For replication, the outer header is re-used, and the Downstream Replication SID is written into the outer IPv6 header destination address. If required, an optional segment list may be used on some branches using H.Encaps.Red (while some other branches may not need that). Note that this H.Encaps.Red is independent from the replication segment – it is just used to steer the replicated traffic on a traffic engineered path to a Downstream node. If SRv6 SID compression is possible , the Replication node SHOULD use a Compressed SID (C-SID) container with Downstream Replication SID as the Last uSID in the container instead of H.Encaps.Red. The above also applies when the Replication segment is for the Root node, whose upstream node has placed the Replication-SID in the header. A local application (e.g. MVPN/EVPN) may also apply H.Encaps.Red and then steer the resulting traffic into the segment. Again note that the H.Encaps.Red is independent of the Replication segment – it is the action of the application (e.g. MVPN/EVPN service). If the service is on a Root node, the two H.Encaps mentioned, one for the service and other in the previous paragraph for replication to Downstream node SHOULD be combined for optimization (to avoid extra IPv6 encapsulation). For the local delivery on a bud/leaf node, the action associated with Replication-SID is “look at next SID in SRH”. The next SID could be a SID with End.DTMC4/6 or End.DT2M local behavior (equivalent of MVPN/EVPN PMSI label in case of tunnel sharing across multiple VPNs). There may also not be a next SID (e.g. MVPN/EVPN with one tunnel per VPN), in which case the Replication-SID is then equivalent to End.DTMC4/6 or End.DT2M. Note that decapsulation is not an inherent action of a Replication segment even on a bud/leaf node. There MAY be SIDs preceding the SRv6 Replication SID in order to guide a packet from a non-adjacent SR node to a Replication Node via an explicit path. A Replication Node MAY steer a replicated packet on an explicit path to a non-adjacent Downstream Node using SIDs it inserts in the copy preceding the downstream Replication SID. The Downstream Node may be leaf node of the Replication Segment, or another Replication Node, or both in case of bud node. For SRv6, as described in above paragraphs, the insertion of SIDs prior to Replication SID entails a new IPv6 encapsulation with SRH, but this can be optimized on Root node or for compressed SRv6 SIDs. Note that locator of Replication SID is sufficient to guide a packet on IGP shortest path, for default or Flex algo, between non-adjacent nodes. A Replication Node MAY use an Anycast SID or BGP PeerSet SID in segment list to send a replicated packet to one downstream Replication node in an Anycast set if and only if all nodes in the set have an identical Replication SID and reach the same set of receivers. There MAY be SIDs after the Replication SID in the SRH of a packet. These SIDs are used to provide additional context for processing a packet locally at the node where the Replication SID is the Active Segment. The processing of SIDs following the Replication SID MUST NOT forward the SRv6 packet to some other node. The restrictions described in this paragraph apply to both un-compressed and compressed SRv6 encapsulation.

ICMPv6 RFC Section 2.4 states an ICMPv6 error message MUST NOT be originated as a result of receiving a packet destined to an IPv6 multicast address. This is to prevent a storm of ICMPv6 error messages resulting from replicated IPv6 packets from overwhelming a source node. There are two exceptions (1) the Packet Too Big message for Path MTU discovery, and (2) Parameter Problem Message, Code 2 reporting an unrecognized IPv6 option. An implementation of Replication Segment for SRv6 MUST enforce this same restrictions and exceptions, though this specification does not use any extension header a future extension may do so and MUST support the exception (2) above.

In the simplest use case, a single Replication segment includes the root node of a multi-point service and the egress/leaf nodes of the service as all the Downstream Nodes. This achieves Ingress Replication that has been widely used for MVPN and EVPN BUM (Broadcast, Unknown and Multicast) traffic. Replication segments can also be used as building blocks for replication trees when Replication segments on the root, intermediate Replication Nodes and leaf nodes are stitched together to achieve efficient replication. That is specified in .

Note to the RFC Editor: Please remove this section and reference to RFC 7942 before publication. This section records the status of known implementations of the protocol defined by this specification at the time of posting of this Internet-Draft, and is based on a proposal described in RFC 7942. The description of implementations in this section is intended to assist the IETF in its decision processes in progressing drafts to RFCs. Please note that the listing of any individual implementation here does not imply endorsement by the IETF. Furthermore, no effort has been spent to verify the information presented here that was supplied by IETF contributors. This is not intended as, and must not be construed to be, a catalog of available implementations or their features. Readers are advised to note that other implementations may exist. According to RFC 7942, "this will allow reviewers and working groups to assign due consideration to documents that have the benefit of running code, which may serve as evidence of valuable experimentation and feedback that have made the implemented protocols more mature. It is up to the individual working groups to use this information as they see fit". There are two known implementations of this draft by Cisco and Nokia. Interoperability reports for the implementations are not applicable since this draft does not specify any inter-operable elements of Replication segments.

Cisco Implementation uses Replication Segments defined in this draft as a basis for PCE to compute and establish P2MP trees in SR domain to provide multi-point services. The implementation, based on latest version of this draft, is in production and supports all MUST and SHOULD clauses for SR-MPLS Replication segments. The documentation is available at Cisco documentation and the point of contact is Rishabh Parekh (riparekh@cisco.com).

Nokia has implemented replication SID as defined in this draft to establish P2MP tree in segment routing domain. The implementation supports SR-MPLS encapsulation and has all the Must and SHOULD clause in this draft. The implementation is at general availability maturity and is compliant with the latest version of the draft. The documentation for implementation can be found at Nokia help and the point of contact is hooman.bidgoli@nokia.com.

IANA has assigned the following codepoint in "SRv6 Endpoint Behaviors" sub-registry of "Segment Routing Parameters" top-level registry for End.Replicate behavior. Value Hex Endpoint behavior Reference 75 0x004B End.Replicate [This.ID]

The security considerations described in RFC 8402, RFC 8986 and RFC 8754 also apply to this document. ICMPv6 specification Section 5.2 describes how the Parameter Problem Message, code 2 exception for ICMPv6 Error message originated for IPv6 multicast destination can be used by a malicious node to cause a denial-of-service attack. Although this specification does not use any extension headers, any future extension doing so is susceptible to the same security consideration.

The authors would like to acknowledge Siva Sivabalan, Mike Koldychev, Vishnu Pavan Beeram, Alexander Vainshtein, Bruno Decraene, Thierry Couture, Joel Halpern and Ketan Talaulikar for their valuable inputs.

Clayton Hassen Bell Canada Vancouver Canada Email: clayton.hassen@bell.ca Kurtis Gillis Bell Canada Halifax Canada Email: kurtis.gillis@bell.ca Arvind Venkateswaran Cisco Systems, Inc. San Jose US Email: arvvenka@cisco.com Zafar Ali Cisco Systems, Inc. US Email: zali@cisco.com Swadesh Agrawal Cisco Systems, Inc. San Jose US Email: swaagraw@cisco.com Jayant Kotalwar Nokia Mountain View US Email: jayant.kotalwar@nokia.com Tanmoy Kundu Nokia Mountain View US Email: tanmoy.kundu@nokia.com Andrew Stone Nokia Ottawa Canada Email: andrew.stone@nokia.com Tarek Saad Cisco Systems Inc. Canada Email:tsaad@cisco.com Kamran Raza Cisco Systems, Inc. Canada Email:skraza@cisco.com

This section illustrates an example of a single Replication segment. Examples showing Replication segment stitched together to form P2MP tree (based on SR P2MP policy) are in . Consider the following topology:

In this example, the Node-SID of a node Rn is N-SIDn and Adjacency-SID from node Rm to node Rn is A-SIDmn. Interface between Rm and Rn is Lmn. The state representation uses "R-SID->Lmn" to represent a packet replication with outgoing replication SID R-SID sent on interface Lmn. Assume a Replication segment identified with R-ID at Replication Node R1 and downstream Nodes R2, R6 and R7. The Replication SID at node n is R-SIDn. A packet replicated from R1 to R7 has to traverse R4. The Replication segment state at nodes R1, R2, R6 and R7 is shown below. Note nodes R3, R4 and R5 do not have state for the Replication segment. Replication segment at R1:

: Replication SID: R-SID1 Replication State: R2: L12> R6: R7: ]]> Replication to R2 steers packet directly to R2 on interface L12. Replication to R6, using N-SID6, steers packet via IGP shortest path to that node. Replication to R7 is steered via R4, using N-SID4 and then adjacency SID A-sID47 to R7. Replication segment at R2:

: Replication SID: R-SID2 Replication State: R2: ]]> Replication segment at R6:

: Replication SID: R-SID6 Replication State: R6: ]]> Replication segment at R7:

: Replication SID: R-SID7 Replication State: R7: ]]> When a packet is steered into the Replication segment at R1: Since R1 is directly connected to R2, R1 performs PUSH operation with just <R-SID2> label for the replicated copy and sends it to R2 on interface L12. R2, as Leaf, performs NEXT operation, pops R-SID2 label and delivers the payload. R1 performs PUSH operation with <N-SID6, R-SID6> label stack for the replicated copy to R6 and sends it to R2, the nexthop on IGP shortest path to R6. R2 performs CONTINUE operation on N-SID6 and forwards it to R3. R3 is the penultimate hop for N-SID6; it performs penultimate hop popping, which corresponds to the NEXT operation and the packet is then sent to R6 with <R-SID6> in the label stack. R6, as Leaf, performs NEXT operation, pops R-SID6 label and delivers the payload. R1 performs PUSH operation with <N-SID4, A-SID47, R-SID7> label stack for the replicated copy to R7 and sends it to R2, the nexthop on IGP shortest path to R4. R2 is the penultimate hop for N-SID4; it performs penultimate hop popping, which corresponds to the NEXT operation and the packet is then sent to R4 with <A-SID47, R-SID1> in the label stack. R4 performs NEXT operation, pops A-SID47, and delivers packet to R7 with <R-SID7> in the label stack. R7, as Leaf, performs NEXT operation, pops R-SID7 label and delivers the payload.

For SRv6 , we use SID allocation scheme, reproduced below, from Illustrations for SRv6 Network Programming 2001:db8::/32 is an IPv6 block allocated by a Regional Internet Registry (RIR) to the operator 2001:db8:0::/48 is dedicated to the internal address space 2001:db8:cccc::/48 is dedicated to the internal SRv6 SID space We assume a location expressed in 64 bits and a function expressed in 16 bits Node k has a classic IPv6 loopback address 2001:db8::k/128 which is advertised in the IGP Node k has 2001:db8:cccc:k::/64 for its local SID space. Its SIDs will be explicitly assigned from that block Node k advertises 2001:db8:cccc:k::/64 in its IGP Function :1:: (function 1, for short) represents the End function with PSP support Function :Cn:: (function Cn, for short) represents the End.X function from to Node n Each node k has: An explicit SID instantiation 2001:db8:cccc:k:1::/128 bound to an End function with additional support for PSP An explicit SID instantiation 2001:db8:cccc:k:Cj::/128 bound to an End.X function to neighbor J with additional support for PSP An explicit SID instantiation 2001:db8:cccc:k:Fk::/128 bound to an End.Replicate function Assume a Replication segment identified with R-ID at Replication Node R1 and downstream Nodes R2, R6 and R7. The Replication SID at node k, bound to an End.Replicate function, is 2001:db8:cccc:k:Fk::/128. A packet replicated from R1 to R7 has to traverse R4. The Replication segment state at nodes R1, R2, R6 and R7 is shown below. Note nodes R3, R4 and R5 do not have state for the Replication segment. The state representation uses "R-SID->Lmn" to represent a packet replication with outgoing replication SID R-SID sent on interface Lmn. Replication segment at R1:

: Replication SID: 2001:db8:cccc:1:F1::0 Replication State: R2: <2001:db8:cccc:2:F2::0->L12> R6: <2001:db8:cccc:6:F6::0> R7: <2001:db8:cccc:4:C7::0, 2001:db8:cccc:7:F7::0> ]]> Replication to R2 steers packet directly to R2 on interface L12. Replication to R6, using 2001:db8:cccc:6:F6::0, steers packet via IGP shortest path to that node. Replication to R7 is steered via R4, using End.X SID 2001:db8:cccc:4:C7::0 at R4 to R7. Replication segment at R2:

: Replication SID: 2001:db8:cccc:2:F2::0 Replication State: R2: ]]> Replication segment at R6:

: Replication SID: 2001:db8:cccc:6:F6::0 Replication State: R6: ]]> Replication segment at R7:

: Replication SID: 2001:db8:cccc:7:F7::0 Replication State: R7: ]]> When a packet, (A,B2), is steered into the Replication segment at R1: Since R1 is directly connected to R2, R1 creates encapsulated replicated copy (2001:db8::1, 2001:db8:cccc:2:F2::0) (A, B2), and sends it to R2 on interface L12. R2, as Leaf, removes outer IPv6 header and delivers the payload. R1 creates encapsulated replicated copy (2001:db8::1, 2001:db8:cccc:6:F6::0) (A, B2) then forwards the resulting packet on the shortest path to 2001:db8:cccc:6::/64. R2 and R3 forward the packet using 2001:db8:cccc:6::/64. R6, as Leaf, removes outer IPv6 header and delivers the payload. R1 creates encapsulated replicated copy (2001:db8::1, 2001:db8:cccc:4:C7::0) (2001:db8:cccc:7:F7::0; SL=1) (A, B2) and sends it to R2, the nexthop on IGP shortest path to 2001:db8:cccc:4::/64. R2 forwards packet to R4 using 2001:db8:cccc:4::/64. R4 executes End.X function on 2001:db8:cccc:4:C7::0, performs PSP action, removes SRH and sends resulting packet (2001:db8::1, 2001:db8:cccc:7:F7::0) (A, B2) to R7. R7, as Leaf, removes outer IPv6 header and delivers the payload.